Skip to content

The only listing here that cites a disc standard by number

EZARC 80921501, 1.5 in rotary, 30 discs and 2 mandrels

The only disc listing in this hub to cite the European safety standard for bonded abrasives by number — alongside the highest published speed rating on the shelf.

EZARC 1.5 inch rotary cut-off wheels in their storage case with mandrels

EZARC 80921501, 1.5 in rotary, 30 discs and 2 mandrels

The only disc listing in this hub to cite the European safety standard for bonded abrasives by number — alongside the highest published speed rating on the shelf.

Amazon reference
B0DNHSC1VW
EAN
0810151450681
  • Publishes a maximum speed of 45,000 rpm, the highest on this shelf and appropriate to a rotary tool
  • Cites EN 12413 by number — the European standard for bonded abrasive safety — and ASM07
  • The title says 32-pack and the storage bullet says 30 discs: the pack is 30 wheels plus 2 mandrels

Best for: Cutting bolts and hardened fasteners with a rotary tool, where the speed rating has to be right

≈ $18
Check price on Amazon

Specifications

Amazon reference
B0DNHSC1VW
EAN
0810151450681

This hub’s introduction names the maximum speed as the first marking to read on any disc, and this is the listing that treats it seriously. Forty-five thousand rpm, which is the right order for a rotary tool rather than an angle grinder, and — alone among the nine American listings here — a citation of the standard behind it: EN 12413, the European safety standard for bonded abrasives, which governs how such a wheel is built, marked and burst-tested.

The rest is specified in the same spirit. A thickness of 0.045 in given also as 1.1 mm (0.04 in). Fiberglass reinforcement. Two mandrels on a 1/8 in arbor, which is what most rotary tools take. A storage case, which matters because a chipped rotary wheel is a wheel to throw away and a loose one in a drawer will chip. And the applications named are the honest ones: hardened steel, bolts, screws, sheet, thin wood.

The count needs one sentence of explanation: the title says 32-pack and the case bullet says thirty discs, because the pack is thirty wheels and two mandrels. Both figures are correct about different things. What is absent, as everywhere on this shelf, is any statement about iron and sulfur — the second marking this hub names, and the one that decides whether a disc should touch stainless.

Availability

Read on the day this page was built: $17 at the American Amazon shop.

Read from Keepa on the day this page was last revised; stock and price both move without notice.

Prices quoted in this text were read on 2026-10-07. The live price is at the top of the page.

The questions welders ask

Is the pack 30 or 32?

Thirty wheels and two mandrels, which is thirty-two pieces. The title counts pieces and the storage bullet counts discs — "a sturdy PP storage case to keep all 30 discs neatly organized" — so both numbers are right about different things. On this shelf that makes it the clearest of the arithmetic discrepancies: another listing says five diameters and lists six, which is not reconcilable at all.

What does citing EN 12413 add?

It names the rules the disc claims to be built to. EN 12413 is the European safety standard for bonded abrasive products: it governs construction, marking and the burst testing that stands behind a maximum speed. A listing that gives an rpm figure is making a claim; a listing that cites the standard the figure was established under is making a checkable one. Of nine disc listings on this shelf, this is the only one that does it.

More cutting & grinding discs

  • Kuenuilr 44-piece rotary cutting set with resin discs, saw blades and diamond wheels

    Kuenuilr d36, 44-piece rotary cutting set

    The only set on this shelf that mixes resin, high speed steel and diamond wheels — on a listing that says five blade diameters and then lists six.

    Amazon reference
    B07WDJ8Q79
    EAN
    0793610636218
    • Three different wheel technologies in one box — resin for metal, HSS for wood and soft metal, diamond for glass and stone
    • HSS blades in a range of diameters, from 22 to 50 mm (0.87 to 1.97 in)
    • Says "5 kinds of outer diameters" and then lists six: 22, 25, 32, 35, 44 and 50 mm (1.97 in)

    Best for: A rotary tool that has to cut metal, wood and glass without three separate purchases

    ≈ $10
    Check price on Amazon
  • NIANNIAN 1-1/4 inch rotary tool cut-off wheels with mandrels

    NIANNIAN QGL-60P, 1-1/4 in rotary, 60-pack

    Sixty small cut-off wheels and four mandrels for a rotary tool, on a listing that calls the same wheel fiberglass in one bullet and diamond in the next.

    Amazon reference
    B08QJFK7V3
    EAN
    0786118470514
    • Sixty wheels, so a disc that glazes or chips is simply replaced
    • Four mandrels included, which is the part that gets lost rather than worn
    • No maximum speed published, on a wheel for a tool that runs to 30,000 rpm or more

    Best for: Cutting bolts, screws and small section with a rotary tool, in quantity

    ≈ $6
    Check price on Amazon
  • panlen 4-1/2 inch cut-off wheels, fifty in a box

    panlen plcw, 4-1/2 in × 0.045 in, 50-pack

    A fifty-disc box that publishes both its rpm and its peripheral speed, and tells you a hundred-pack exists — the format for a workshop that cuts every week.

    Amazon reference
    B08FR63K33
    EAN
    0664248791979
    • Fifty discs, which brings the price per disc to a fraction of the small packs on this shelf
    • Publishes 13,300 rpm and 80 m (262 ft)/s, the two forms of the same limit
    • Nothing about iron and sulfur content, while claiming stainless suitability

    Best for: A workshop where discs are a running cost rather than a purchase

    ≈ $25
    Check price on Amazon

Elsewhere in the workroom

  • DKIBBITH titanium combination drill and tap bits in six SAE sizes

    DKIBBITH DKVIP-003, SAE drill-tap, 6-pack

    Six combination bits covering the common small SAE threads, on a listing that tells you the single mistake that strips a thread.

    Amazon reference
    B08JZDWZ9P
    EAN
    0791715205667
    • Six genuinely different sizes — 6-32, 8-32, 10-24, 10-32, 12-24 and 1/4-20 UNC
    • Covers both pitches of the #10 thread, 10-24 and 10-32, which matters more than it looks
    • Titanium coating wears off the cutting edge quickly; the nitrided set at the same price hardens the steel itself

    Best for: The common small machine screw threads, in aluminum and thin steel

    ≈ $15
    Check price on Amazon
  • Drill America 1/2 inch NPT pipe tap with its matching 23/32 inch drill bit

    Drill America POU1/2NPTW/DRILL, 1/2 in NPT tap and 23/32 in drill

    The only product in this hub that answers the question the shelf is built on — which drill goes with which tap — by putting the two in the same bag.

    Amazon reference
    B01MG92FX1
    EAN
    0887861241854
    • Supplies the tap and its matching tapping drill together — the exact thing this hub’s introduction says stops threads tearing out
    • Publishes both sizes: a 1/2 in NPT tap and a 23/32 in drill
    • A carbon steel tap, which is softer than HSS and intended for chasing an existing thread rather than cutting a new one in solid steel

    Best for: Cutting or recutting a 1/2 in NPT pipe thread without guessing the tapping drill

    ≈ $18
    Check price on Amazon
  • KOOPOOL 114-piece ratcheting tap and die set laid out in its case

    KOOPOOL 114-piece ratcheting tap and die set

    The only set in this hub that supplies the tapping drills alongside the taps, with the thread tolerance classes and the heat treatment both published.

    Amazon reference
    B0GKG5LNHF
    EAN
    0671891089407
    • Supplies 34 matched HSS drill bits alongside the 68 taps and dies — the tapping drill question answered in the same case
    • Publishes the thread tolerance classes: 6H for metric internal threads and 2B for UNC
    • The highest price on this shelf by a factor of three

    Best for: A workshop that cuts and repairs threads across both systems and wants one case for all of it

    ≈ $100
    Check price on Amazon

All cutting & grinding discs