Skip to content

Vice · System 16

WELDINGER Vice 100 mm for System 16 welding tables

A vice that drops into a 16 mm (0.63 in) fixture-table hole — clamping where the work is, not at the bench edge.

WELDINGER Vice 100 mm for System 16 welding tables, product photograph

WELDINGER Vice 100 mm for System 16 welding tables

A vice that drops into a 16 mm (0.63 in) fixture-table hole — clamping where the work is, not at the bench edge.

Jaw width
100 mm (3.94 in)
Fitment
System 16 — 16 mm (0.63 to 0.63 in) table holes
Amazon reference
B0CQD4ZX3C
EAN
4255607911037
  • Mounts anywhere on a fixture table, not just at the edge
  • System 16 is a widespread standard for welding tables
  • Verified on the German store only at the time of checking

Best for: Owners of a fixture table who need to grip rather than just clamp down

Search Amazon for this model

Specifications

Jaw width
100 mm (3.94 in)
Fitment
System 16 — 16 mm (0.63 to 0.63 in) table holes
Amazon reference
B0CQD4ZX3C
EAN
4255607911037

Check the hole size first

System 16 or System 28 — measure a table hole before ordering. It is a hard fitment, not a tolerance.

Availability

No such listing: the American Amazon shop answers the reference with a search box rather than a page.

Read from Keepa on the day this page was last revised; stock and price both move without notice.

Sources

Every figure above comes from the manufacturer’s published specification for this reference. Fields the listing does not publish are left out rather than estimated. Market availability was verified per market on the EAN.

The questions welders ask

What is System 16?

A welding-table standard built around 16 mm (0.63 in) diameter holes on a regular grid. Clamps, stops, squares and vices all use the same 16 mm (0.63 in) spigot, so any accessory drops into any hole. System 28 is the heavier industrial equivalent. The number is the hole diameter, and accessories are not interchangeable between the two.

Why not just use a bench vice?

Because a bench vice is at the edge of the bench and the work is in the middle. A table-mounted vice grips exactly where the assembly is, which means fewer awkward overhangs and less work held by hand — the practical difference a fixture table exists to make.

Welders this fits

More clamps & vices

  • Three HEIHAK 18 inch locking C-clamps with swivel pads

    HEIHAK 06231043, 18 in, 3-pack

    Three big locking clamps that publish both the figures that matter — a 7.8 in throat and a 6.3 in opening, the deepest and widest in this hub.

    Amazon reference
    B0B4V3WN28
    EAN
    0755621348443
    • A 7.8 in throat depth, more than twice the next deepest clamp on this shelf
    • A 6.3 in maximum opening, which takes stacked plate or heavy box section
    • An 18 in plier is heavy and awkward on small work — these are not detail clamps

    Best for: Clamping a plate or a frame well in from the edge, where a short-throat clamp cannot reach the seam

    ≈ $31
    Check price on Amazon
  • Set of nickel-plated 6 inch locking C-clamp pliers

    Biugaaufai 6 Inch locking C-clamp set

    A set of 6-inch locking clamps whose own listing cannot agree on how many are in the box.

    Amazon reference
    B0DNFD3KD7
    EAN
    0729767456652
    • Several clamps in one purchase, which is how a frame actually gets held
    • Nickel-plated alloy steel, stated
    • The title says "6 Pack" and the first bullet says "four 6-inch C-Clamp pliers" — the quantity is not settled anywhere on the page

    Best for: Small work and body panels, where several modest clamps beat one large one

    ≈ $33
    Check price on Amazon
  • KAKA Industrial cast iron 90 degree angle clamp holding two square tubes

    KAKA INDUSTRIAL AC-100

    The only clamp on this shelf that holds a right angle on its own, bolted to a bench — with a copper-plated screw so spatter does not weld to the thread.

    Amazon reference
    B0159ZUQ22
    EAN
    0745369240840
    • Holds a true 90 degrees mechanically, which is what this hub’s buying tip says magnets cannot do
    • Publishes all three jaw dimensions — 4 in opening, 2-1/4 in height, 3-1/2 in width
    • The listing calls 26 lb a "lightweight design" in the same sentence that publishes the figure

    Best for: Repeating the same square corner, where the clamp sets the angle instead of a magnet suggesting it

    ≈ $155
    Check price on Amazon

Elsewhere in the workroom

  • Shark Welding 4.5 inch cut-off wheels in a ten-pack

    Shark Welding 13067, 4.5 in × 1/16 in, 10-pack

    The only disc on this shelf with a published grit size, and the thickest cutting wheel here at 1/16 in — which is a different tool from a 0.045 in disc.

    Amazon reference
    B00IRIRMVC
    EAN
    0682488130679
    • Publishes a grit size — 46 — which no other disc listing in this hub does
    • A 1/16 in thickness, nearly 40 per cent thicker than the 0.045 in wheels here, so it resists flexing in a deep cut
    • No maximum speed published, the first marking this hub names

    Best for: Heavier cutting where a thin wheel flexes or wears through too fast

    ≈ $37
    Check price on Amazon
  • United Abrasives-SAIT Type 27 depressed center grinding wheels

    United Abrasives 20064, Type 27 4-1/2 × 1/4 in, 25-pack

    A professional ceramic grinding wheel in a 25-pack — the only ceramic abrasive in this hub, on a listing with no speed rating and one bullet repeated word for word.

    Amazon reference
    B002C7BL8O
    EAN
    0699053200644
    • Ceramic aluminum oxide grain — the only ceramic abrasive in this hub, and a genuinely different material from brown or white alumina
    • A Type 27 depressed center, which is what lets a grinding wheel work at a shallow angle without the nut fouling
    • No maximum speed published anywhere, on a 1/4 in grinding wheel

    Best for: Grinding stainless and high tensile alloys in quantity, where grain quality decides the cost per weld

    ≈ $200
    Check price on Amazon
  • United Abrasives-SAIT A36T 3 inch cut-off wheels, hundred pack

    United Abrasives 23052, A36T 3 in × .035 in, 100-pack

    The largest pack in this hub and one of four listings here to publish a speed rating — on a description that says the wheels are externally reinforced and then internally reinforced.

    Amazon reference
    B003IT5TT2
    EAN
    0699053230528
    • Publishes a maximum speed — 25,000 rpm — and names the tool it is for, a die grinder
    • Publishes the full specification: 3 in diameter, .035 in thickness, 1/4 in arbor
    • The description says the wheels are "externally reinforced with fiberglass layers" and then, two sentences later, "internally reinforced with the highest quality fiberglass"

    Best for: A die grinder in production use, cutting bolts, tube and weld tabs all day

    ≈ $255
    Check price on Amazon

All clamps & vices